Troubleshooting Booting on the x86 Platform (Task Map)
x86: Troubleshooting Error Messages Upon System Boot
If any multiboot entries that support directly booting the unix kernel are encountered
by GRUB, the following message is displayed:
multiboot is no longer used to boot the Solaris Operating System.
The grub entry should be changed to:
kernel$ /boot/$ISADIR/xen.gz
module$ /platform/i86xpv/kernel/$ISADIR/unix /platform/i86xpv/kernel/$ISADIR/unix -B $ZFS-BOOTFS
module$ /platform/i86pc/$ISADIR/boot_archive
See https://www.sun.com/msg/SUNOS-8000-AK for details.
Press any key to reboot.
If the preceding message is displayed, you will need to update the
entries in the GRUB menu.lst manually to successfully boot the system. More information can
be found at https://www.sun.com/msg/SUNOS-8000-AK and the boot(1M) man page. For further information and
instructions, see x86: Error Messages Upon System Boot.
x86: How to Stop a System for Recovery Purposes
- Stop the system by using one of the following commands, if possible:
If the keyboard and mouse are functional, become superuser. Then, type init 0 to stop the system. After the Press any key to reboot prompt appears, press any key to reboot the system.
If the keyboard and mouse are functional, become superuser. then, type init 6 to reboot the system.
- If the system does not respond to any input from the mouse or
the keyboard, press the Reset key, if it exists, to reboot the
system.
Or, you can use the power switch to reboot the system.
x86: Forcing a Crash Dump and Reboot of the System
Forcing a crash dump and reboot of the system are sometimes necessary for
troubleshooting purposes. The savecore feature is enabled by default.
For more information about system crash dumps, see Chapter 17, Managing System Crash Information (Tasks), in System Administration Guide: Advanced Administration.
x86: How to Force a Crash Dump and Reboot of the System
If you cannot use the reboot -d or the halt -d command, you
can use the kernel debugger, kmdb, to force a crash dump. The kernel
debugger must have been loaded, either at boot, or with the mdb -k
command, for the following procedure to work.
Note - You must be in text mode to access the kernel debugger (kmdb).
So, first exit any window system.
- Access the kernel debugger.
The method used to access the debugger is dependent upon the type
of console that you are using to access the system.
If you are using a locally attached keyboard, press F1–A.
If you are using a serial console, send a break by using the method appropriate to that type of serial console.
The kmdb prompt is displayed.
- To induce a crash, use the systemdump macro.
[0]> $<systemdump
Panic messages are displayed, the crash dump is saved, and the system reboots.
- Verify that the system has rebooted by logging in at the console login
prompt.
Example 13-6 x86: Forcing a Crash Dump and Reboot of the System by Using halt -d
This example shows how to force a crash dump and reboot of
the x86 based system neptune by using the halt -d and boot commands.
Use this method to force a crash dump of the system. Reboot the
system afterwards manually.
# halt -d
4ay 30 15:35:15 wacked.Central.Sun.COM halt: halted by user
panic[cpu0]/thread=ffffffff83246ec0: forced crash dump initiated at user request
fffffe80006bbd60 genunix:kadmin+4c1 ()
fffffe80006bbec0 genunix:uadmin+93 ()
fffffe80006bbf10 unix:sys_syscall32+101 ()
syncing file systems... done
dumping to /dev/dsk/c1t0d0s1, offset 107675648, content: kernel
NOTICE: adpu320: bus reset
100% done: 38438 pages dumped, compression ratio 4.29, dump succeeded
Welcome to kmdb
Loaded modules: [ audiosup crypto ufs unix krtld s1394 sppp nca uhci lofs
genunix ip usba specfs nfs md random sctp ]
[0]>
kmdb: Do you really want to reboot? (y/n) y
x86: How to Boot a System With the Kernel Debugger in the GRUB Boot Environment (kmdb)
This procedure shows the basics for loading the kernel debugger (kmdb). The
savecore feature is enabled by default. For more detailed information about using the
kernel debugger, see the Solaris Modular Debugger Guide.
- Boot the system.
The GRUB menu is displayed when the system is booted.
- When the GRUB menu is displayed, type e to access the GRUB edit
menu.
- Use the arrow keys to select the kernel$ line.
If you cannot use the arrow keys, use the ^ key to scroll
up and the v key to scroll down.
- Type e to edit the line.
The boot entry menu is displayed. In this menu, you can modify Solaris
boot behavior by adding additional boot arguments to the end of the kernel$
line.
- Type -k at the end of the line.
- Press enter to return to the GRUB main menu.
- Type b to boot the system with the kernel debugger enabled.
- Access the kernel debugger.
The method used to access the debugger is dependent upon the type
of console that you are using to access the system:
If you are using a locally attached keyboard, press F1–A.
If you are using a serial console, send a break by using the method appropriate to that type of serial console.
A welcome message is displayed when you access the kernel debugger for the
first time.
Example 13-7 x86: Booting a System With the Kernel Debugger (Hypervisor Support)
This example shows how to boot a 64-bit capable x86 based system,
with the kernel debugger enabled:
kernel$ /boot/$ISADIR/xen.gz
module$ /platform/i86xpv/kernel/$ISADIR/unix /platform/i86xpv/kernel/$ISADIR/unix -B $ZFS-BOOTFS -k
This example shows how to boot a 64-bit capable x86 based system
in 32-bit mode, with the kernel debugger enabled:
kernel$ /boot/xen.gz
module$ /platform/i86xpv/kernel/unix /platform/i86xpv/kernel/unix -B $ZFS-BOOTFS -k
Example 13-8 x86: Booting a System With the Kernel Debugger (Support for Directly Loading and Booting the unix Kernel)
The following examples apply to a Solaris release with GRUB support for directly
loading and booting the unix kernel.
This example shows how to boot a 64-bit capable x86 based system,
with the kernel debugger enabled.
kernel$ /platform/i86pc/kernel/$ISADIR/unix -B $ZFS-BOOTFS -k
This example shows how to boot a 64-bit capable x86 based system
in 32-bit mode, with the kernel debugger enabled.
kernel$ /platform/i86pc/kernel/unix -B $ZFS-BOOTFS -k
Example 13-9 x86: Booting a System With the Kernel Debugger (GRUB Multiboot Implementation)
This example shows how to manually boot a 64-bit capable x86 based
system with the kernel debugger enabled.
kernel$ /platform/i86pc/multiboot kernel/amd64/unix -k -B $ZFS-BOOTFS
This example shows how to boot a 64-bit capable x86 based system
32-bit mode with the kernel debugger enabled.
kernel$ /platform/i86pc/multiboot kernel/unix -k -B $ZFS-BOOTFS
