Follow Techotopia on Twitter

On-line Guides
All Guides
eBook Store
iOS / Android
Linux for Beginners
Office Productivity
Linux Installation
Linux Security
Linux Utilities
Linux Virtualization
Linux Kernel
System/Network Admin
Programming
Scripting Languages
Development Tools
Web Development
GUI Toolkits/Desktop
Databases
Mail Systems
openSolaris
Eclipse Documentation
Techotopia.com
Virtuatopia.com
Answertopia.com

How To Guides
Virtualization
General System Admin
Linux Security
Linux Filesystems
Web Servers
Graphics & Desktop
PC Hardware
Windows
Problem Solutions
Privacy Policy

  




 

 

6.6. The buffermem parameters

The buffermem file is also closely related to the operation of the virtual memory VM subsystem of the Linux kernel. The value in this file /proc/sys/vm/buffermem controls how much memory should be used for buffer memory in percentage. It is important to note that the percentage is calculated as a percentage of total system memory.

The default setup for the buffermem parameters under Red Hat Linux is: "2 10 60"

Version 6.1 only

To change the values of buffermem, type the following command on your terminal:
            [root@deep] /# echo "70 10 60" >/proc/sys/vm/buffermem
            
You may add the above commands to the /etc/rc.d/rc.local script file and you'll not have to type it again the next time you reboot your system.

Version 6.2 only

Edit the /etc/sysctl.conf file and add the following line:
            # Improve virtual memory performance
            vm.buffermem = 70 10 60
            
You must restart your network for the change to take effect. The command to manually restart the network is the following:
            [root@deep] /# /etc/rc.d/init.d/network restart
            

Setting network parameters [ OK ] Bringing up interface lo [ OK ] Bringing up interface eth0 [ OK ] Bringing up interface eth1 [ OK ]

According to the /usr/src/linux/Documentation/sysctl/vm.txt file, the first parameter 80 % means to use a minimum of 80 percent of memory for the buffer cache; the minimum percentage of memory that should be spent on buffer memory.The last two parameters 10 and 60 are unused by the system so we dont need to change the defaults.

Depending of the amount of RAM you have in the server the value of 80% may vary. When your server is highly loaded and when all application are used, you can know in detail how much memory are required and used by the system. 80 % for the buffermem parameters seem to be too much for systems under 256 MB of RAM. Doing a free -m command on the prompt your system will display amount of free and used memory in the system. Once you have executed this command free -m, check for -/+ buffers/cache:values and get the one related to the minimal (-) to set your value for buffermem.

Example 6-1. For 128 MB of RAM

              128 * 80% = 102.4 MB
              128 - 102.4 = 25.6 MB
              
                [root@deep] /#free -m
                

                              total       used       free     shared    buffers       cached
                Mem:            124        121          3         30         43           48
                -/+ buffers/cache:          29         95
                Swap:           128          2        126
                
The result shows us that the -/+ buffers/cache: need 29 MB at minimum to run the system properly and with 128 MB of RAM set at 80% we have only 25.6 MB available. Hmmm! problem, i guess. so we go back to the calculator again and do this:
                128 * 70% = 89.6
                128 - 89.6 = 38.4 MB                
              
well solved good!.

Tip: Look at /usr/src/linux/Documentation/sysctl/vm.txt for more information on how to improve kernel parameters related to virtual memory.

 
 
  Published under the terms of the Open Publication License Design by Interspire