Follow Techotopia on Twitter

On-line Guides
All Guides
eBook Store
iOS / Android
Linux for Beginners
Office Productivity
Linux Installation
Linux Security
Linux Utilities
Linux Virtualization
Linux Kernel
System/Network Admin
Programming
Scripting Languages
Development Tools
Web Development
GUI Toolkits/Desktop
Databases
Mail Systems
openSolaris
Eclipse Documentation
Techotopia.com
Virtuatopia.com
Answertopia.com

How To Guides
Virtualization
General System Admin
Linux Security
Linux Filesystems
Web Servers
Graphics & Desktop
PC Hardware
Windows
Problem Solutions
Privacy Policy

  




 

 

NOTE: CentOS Enterprise Linux 5 is built from the Red Hat Enterprise Linux source code. Other than logo and name changes CentOS Enterprise Linux 5 is compatible with the equivalent Red Hat version. This document applies equally to both Red Hat and CentOS Enterprise Linux 5.

39.6. Verifying the Boot Loader

The kernel RPM package configures the boot loader to boot the newly installed kernel (except for IBM eServer iSeries systems). However, it does not configure the boot loader to boot the new kernel by default.

It is always a good idea to confirm that the boot loader has been configured correctly. This is a crucial step. If the boot loader is configured incorrectly, the system will not boot into Red Hat Enterprise Linux properly. If this happens, boot the system with the boot media created earlier and try configuring the boot loader again.

39.6.1. x86 Systems

All x86 systems (including all AMD64 systems) use GRUB as the boot loader.

39.6.1.1. GRUB

Confirm that the file /boot/grub/grub.conf contains a title section with the same version as the kernel package just installed

# Note that you do not have to rerun grub after making changes to this file 
# NOTICE:  You have a /boot partition.  This means that 
#          all kernel and initrd paths are relative to /boot/, eg. 
#          root (hd0,0) 
#          kernel /vmlinuz-version ro root=/dev/hda2 
#          initrd /initrd-version.img 
#boot=/dev/hda 
default=1 timeout=10 
splashimage=(hd0,0)/grub/splash.xpm.gz 
title Red Hat Enterprise Linux (2.6.9-5.EL)
         root (hd0,0)
	 kernel /vmlinuz-2.6.9-5.EL ro root=LABEL=/         
	 initrd /initrd-2.6.9-5.EL.img 
title Red Hat Enterprise Linux (2.6.9-1.906_EL)
         root (hd0,0)         
	 kernel /vmlinuz-2.6.9-1.906_EL ro root=LABEL=/         
	 initrd /initrd-2.6.9-1.906_EL.img

If a separate /boot/ partition was created, the paths to the kernel and initrd image are relative to /boot/.

Notice that the default is not set to the new kernel. To configure GRUB to boot the new kernel by default, change the value of the default variable to the title section number for the title section that contains the new kernel. The count starts with 0. For example, if the new kernel is the first title section, set default to 0.

Begin testing the new kernel by rebooting the computer and watching the messages to ensure that the hardware is detected properly.

39.6.2. Itanium Systems

Itanium systems use ELILO as the boot loader, which uses /boot/efi/EFI/redhat/elilo.conf as the configuration file. Confirm that this file contains an image section with the same version as the kernel package just installed:

prompt timeout=50 default=old  image=vmlinuz-2.6.9-5.EL
         label=linux         
	 initrd=initrd-2.6.9-5.EL.img         read-only         
	 append="root=LABEL=/" image=vmlinuz-2.6.9-1.906_EL         
	 label=old         
	 initrd=initrd-2.6.9-1.906.img         read-only         
	 append="root=LABEL=/"

Notice that the default is not set to the new kernel. To configure ELILO to boot the new kernel, change the value of the default variable to the value of the label for the image section that contains the new kernel.

Begin testing the new kernel by rebooting the computer and watching the messages to ensure that the hardware is detected properly.

39.6.3. IBM S/390 and IBM System z Systems

The IBM S/390 and IBM System z systems use z/IPL as the boot loader, which uses /etc/zipl.conf as the configuration file. Confirm that the file contains a section with the same version as the kernel package just installed:

[defaultboot] default=old target=/boot/ 
[linux]
         image=/boot/vmlinuz-2.6.9-5.EL         
	 ramdisk=/boot/initrd-2.6.9-5.EL.img         
	 parameters="root=LABEL=/" 
[old]
         image=/boot/vmlinuz-2.6.9-1.906_EL         
	 ramdisk=/boot/initrd-2.6.9-1.906_EL.img         
	 parameters="root=LABEL=/"

Notice that the default is not set to the new kernel. To configure z/IPL to boot the new kernel by default, change the value of the default variable to the name of the section that contains the new kernel. The first line of each section contains the name in brackets.

After modifying the configuration file, run /sbin/zipl as root to enable the changes.

Begin testing the new kernel by rebooting the computer and watching the messages to ensure that the hardware is detected properly.

39.6.4. IBM eServer iSeries Systems

The /boot/vmlinitrd-<kernel-version> file is installed when you upgrade the kernel. However, you must use the dd command to configure the system to boot the new kernel:

  1. As root, issue the command cat /proc/iSeries/mf/side to determine the default side (either A, B, or C).

  2. As root, issue the following command, where <kernel-version> is the version of the new kernel and <side> is the side from the previous command:

    dd if=/boot/vmlinitrd-<kernel-version> of=/proc/iSeries/mf/<side>/vmlinux bs=8k

Begin testing the new kernel by rebooting the computer and watching the messages to ensure that the hardware is detected properly.

39.6.5. IBM eServer pSeries Systems

IBM eServer pSeries systems use YABOOT as the boot loader, which uses /etc/aboot.conf as the configuration file. Confirm that the file contains an image section with the same version as the kernel package just installed:

boot=/dev/sda1 init-message=Welcome to Red Hat Enterprise Linux! Hit <TAB> for boot options   
partition=2 timeout=30 install=/usr/lib/yaboot/yaboot delay=10 nonvram  
image=/vmlinux--2.6.9-5.EL
         label=old         
	 read-only       
	 initrd=/initrd--2.6.9-5.EL.img        
	 append="root=LABEL=/"   
image=/vmlinux-2.6.9-5.EL         
	 label=linux       
	 read-only       
	 initrd=/initrd-2.6.9-5.EL.img         
	 append="root=LABEL=/"

Notice that the default is not set to the new kernel. The kernel in the first image is booted by default. To change the default kernel to boot either move its image stanza so that it is the first one listed or add the directive default and set it to the label of the image stanza that contains the new kernel.

Begin testing the new kernel by rebooting the computer and watching the messages to ensure that the hardware is detected properly.


 
 
  Published under the terms of the GNU General Public License Design by Interspire